FL641F pneumatic discharge valve

FL641F pneumatic discharge valve
  • sell:021-32051999
  • sell:021-32050777
  • fax:021-66099555

Details

  • Product Introduction
  • Service Promise
  • Ordering Process

Corrosion resistance

1. Pneumatic discharge valve uses medium such as water, acetone, alcohol, ammonia, barium carbonate, benzene (WCB material minimum temperature is - 290C, maximum temperature is 4250 C).

2. Pneumatic discharging valve uses medium such as particle, oil, pulp, carbon dioxide gas (stainless steel material minimum use temperature is - 1000C, maximum use temperature is 23 20C).

3. Pneumatic discharge valve forbids the use of ionic liquids containing fluorine (such as HF etc.) can not use strong alkali and phosphoric acid (temperature > 1500C concentration > 30%).

Two. General working temperature of stainless steel: less than 1500C

Three, pressure range: 0.6~2.5MPa

Four. Path size: 25~250mm

Valve pneumatic device

Pneumatic valve drive device is safe, reliable, low cost, easy to use and maintain, is a valve drive mechanism in a major branch. The working pressure of pneumatic technology is lower, usually greater than 0.82 MPa, and the total thrust of pneumatic device can not be very large because of the size of the structure should not be too large.

Conditions for use of pneumatic devices


气源工作压力
0.4~0.7MPa
环境温度和介质温度
5~60℃
活塞工作速度和叶片外线速度
10~500mm/s
电磁控制信号电流
4~20mA


Classification of pneumatic devices

Valve pneumatic device is divided into three types according to its structural characteristics: membrane pneumatic device, cylinder type pulling device, pendulum pneumatic device. There is also a pull motor type pullout device.

Composition of pneumatic device


薄膜式
气缸式
摆动式
薄膜气缸
膜片
弹簧
活塞杆
气缸
活塞与活塞环
活塞杆
手动操作机构
气动附件
缸体
定子
转子
叶片
盘形膜片
平膜片
单气缸
双气缸
O型密封圈
J型密封圈
U型密封圈
V型密封圈
Y型密封圈
回路系统
信号返回器
空气过滤器
调压阀油雾器
控制换向阀


Material of main parts


零件名称
ZG1Cr18 Ni9Ti系列
ZG00Cr18 Ni10系列
ZG1Cr18 Ni12MO 2 Ti系列
ZG00Cr17Ni14MO 2 系列
WCB系列
阀体/阀盖
ZG1Cr18 Ni9Ti
ZG00Cr18 Ni10
ZG1Cr18 Ni12MO 2 Ti
ZG00Cr17Ni14MO 2
WCB
阀杆
ZG1Cr18 Ni9Ti
ZG00Cr18 Ni10
ZG1Cr18 Ni12MO 2 Ti
ZG00Cr17Ni14MO 2
WCB
阀瓣
ZG1Cr18 Ni9Ti
ZG00Cr18 Ni10
ZG1Cr18 Ni12MO 2 Ti
ZG00Cr17Ni14MO 2
WCB
垫片
304+PTFE
304L+PTFE
316+PTFE
316L+PTFE
石墨+304
螺柱
1Cr17Ni2
1Cr17Ni2
1Cr17Ni2
1Cr17Ni2
35CrMoA
螺母
1Cr18 Ni9Ti
1Cr18 Ni9Ti
1Cr18 Ni9Ti
1Cr18 Ni9Ti
45


Connection size


DN
上法兰
上法兰
下法兰
密封座
D1
D2
D3
D4
D5
D6
25
115
80
115
85
32
135
100
135
100
40
145
110
145
110
80
60
50
165
125
160
125
85
70
65
180
145
180
145
130
85
80
195
160
195
160
135
95
100
215
180
215
180
160
130
125
245
210
245
210
160
140
150
280
240
280
240
185
165
200
335
295
335
295
/
/


The best quality, first-class service Qigao creates more value for you!

"Qigao Valve" expects to continuously improve service quality and strive for excellence. "Sincere service" is the eternal theme of "Qigao". "Qigao" strictly followsIS09001-2000 Quality system certification requirements, strict quality control, responsibility to people, to ensure the healthy operation of production, sales and service. Strengthen communication with users and provide quality products to our customers with perfection and perfect service. Hereby our factory makes the following commitments:

Product Standards:

Products in strict accordance with ChinaGB、HG Standard and USAPISuch as standard design, manufacturing, acceptance. The hardness of the sealing surface meets the requirements of the state and the width exceeds the national standard.

pre-sale service:

Product introduction, technical exchange, non-standard product design, troubleshooting。

Sale service:

A trustworthy contract guarantees timely delivery and keeps in touch with customers. For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.

After sales service:

1、"Qigao" brand product quality period is from the factory12In the month, the implementation of the "three guarantees" service (return, replacement, warranty).

2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions, so as to further improve product quality.

3、Respond quickly to the quality of user complaints, after-sales service personnel rushed to the scene in 24-36 hours (48 hours outside the province).

4、For after-sales service, users are required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of Qigao.

1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:

a、Structure length;

b、Connection Type;

c、Nominal diameter, full diameter, reduced diameter, pipe size;

d、Operating medium and temperature, pressure range;

e、Tests, inspection standards and other requirements

2、The factory can configure various types of driving devices according to customer's specific requirements.。

3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.

4、For futures and order customers, please call us in advance to tell the required valve model, specification, quantity, delivery time and location, and timely transfer to the factory account according to the total 30% deposit or full payment. The rest of the payment is pending. Import before shipment to arrange delivery in time.

 

Order Process:

1、Customer purchase list fax to021-33872143,Or call us 021-33872141

2、Receive customer purchase list, provide valve model selection and quotation (price list)。

3、Specific agreement: delivery date, special requirements, etc.。

download Google:

1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:

a、Structure length;

b、Connection Type;

c、Nominal diameter, full diameter, reduced diameter, pipe size;

d、Operating medium and temperature, pressure range;

e、Tests, inspection standards and other requirements

2、The factory can configure various types of driving devices according to customer's specific requirements.。

3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.

4、For futures and order customers, please call us first to tell the required valve model, specifications, quantity, delivery time and location, and press the total30%The deposit or full payment will be remitted to our factory account in time., The rest of the payment will be remitted before shipment to arrange delivery in time.。

Sale service:

Trustworthy contract, guarantee timely delivery, keep in touch with customers at any time。

For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.

After sales service:

1、"Qigao" product quality period is from the factory12Month, practiceThree packsService (return, replacement, warranty)。

2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions.,
In order to further improve product quality。

3、Respond quickly to the quality of user complaints, after-sales service personnel24-36Hours (outside the province48Hour) rushed to the scene。

4、For after-sales service, the user is required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of “Qigao”.。

statement

  1. All text, data and pictures in this article are for reference only.FL641F pneumatic discharge valvePlease contact us at 4000-700-665 for details of performance, size and price.
  2. If there is no explanation, this article is original, reprint, please indicate the address of this article, thank you for your cooperation!