Q47F fixed ball valve
- sell:021-32051999
- sell:021-32050777
- fax:021-66099555
Details
- Product Introduction
- Service Promise
- Ordering Process
Pneumatic fixed ball valve | Electric fixed ball valve |
Q47F fixed ball valve has two-block and three-block valve body structure, the middle flange bolted, sealed with reinforced PTFE inlaid in stainless steel ring, ring back without spring to ensure that the valve seat close to the ball, keep sealed. There is no PTFE bearing on the upper and lower stem, reducing friction and labor-saving operation. There is no adjusting plate at the bottom of the small shaft to ensure the joint position between the ball and the sealing ring. Full diameter: valve flow aperture is consistent with inner diameter of pipeline, so that pipeline can be cleaned.
Applicable medium: water, gas, oil, natural gas and acid alkali corrosive medium.
Applicable temperature: -196 ~ 350 C
Driving mode: manual, pneumatic, electric, hydraulic and so on.
Nominal diameter: DN25-8001 "to 32"
Product features of fixed ball valves
(1) Labor-saving operation: the sphere is supported by upper and lower bearings to reduce friction, eliminating excessive torque caused by the enormous sealing load formed by the imported pressure pushing the sphere and the seal seat.
(2) Reliable sealing performance: PTFE single material seal ring embedded in the stainless steel valve seat, metal valve seat end with spring to ensure sufficient preload sealing ring, valve in the use of the process of wear and tear sealing surface, under the action of the spring valve to continue to ensure good sealing performance.
(3) Fire-proof structure: In order to prevent PTFE seal ring from burning down and large leakage due to sudden heat or fire, and to encourage fire, a fire-proof seal ring is arranged between the ball and the valve seat. When the seal ring is burned down, the valve seat seal ring is rapidly pushed to the ball under the action of spring force, forming a metal and metal seal. Seal, to a certain degree of sealing effect. The fire test meets the requirements of APl6FA and APl607 standards.
(4) Automatic pressure relief function: when the dielectric pressure in the valve cavity is abnormally high and exceeds the spring preload, the valve seat will retreat from the sphere to achieve the effect of automatic pressure relief, and the valve seat will automatically reset after pressure relief.
(5) Discharge pipeline: Valve body is set up above and below the discharge L, can check whether the valve seat leakage, in the work, when the valve is fully open or closed, unload the pressure in the cavity, can directly replace the filler; can discharge the cavity residue, reduce the media pollution to the valve. Auxiliary seal setting system (customer need to explain when ordering)
(6) The valve is designed with an auxiliary seat emergency sealing system. Once the seal is damaged or the emergency situation occurs and can not be sealed, the sealing surface can be repaired by injecting the corresponding sealant into the sealing surface through the auxiliary sealing system to achieve emergency sealing. When the conveying medium is dirty or contains a small amount of particles, in order to protect the sealing surface and ensure reliable sealing, the device can also be injected with the corresponding cleaning agent or lubricant to clean the sealing surface.
(7) Electric fixed ball valves are widely used for cutting off or circulating the medium of transportation pipelines such as food, medicine, petroleum, chemical industry, natural gas, steel, environmental protection, paper making, etc. The corresponding cleaning agent or lubricant can be injected into the device to clean the sealing surface.
Specification for fixed ball valves
设计依据 | 国标系列 | 美标系列 | |
设计标准 | GB/T12237 | AP16D | ANSI B16.34 |
法兰连接结构长度 | GB/T12221 | AP16D | ANSI B16.10 |
结构长度(焊接) | GB/T15188.1 | AP16D | ANSI B16.10 |
连接法兰 | GB/T9113 JB/T79 Hg20592 | ANSI B16.5、B16.47 | |
对焊端 | GB/T12224 | ANSI B16.25 | |
试验和检验 | GB/T9092 | AP16D | AP1598 |
Pressure grade | Test pressure(MPa) | ||
公称压力(PN) | 磅级(Class) | 壳体试验 | 密封试验 |
1.0 | - | 1.5 | 1.1 |
1.6 | - | 2.5 | 1.76 |
2.5 | - | 3.8 | 2.75 |
4.0 | - | 6.0 | 4.4 |
6.4 | - | 9.6 | 7.04 |
- | 150 | 3.0 | 2.2 |
- | 300 | 7.6 | 5.6 |
- | 600 | 15.0 | 11.0 |
- | 10K | 2.4 | 1.5 |
- | 20K | 5.8 | 4.0 |
Serial number | Part name | Texture of material | |
GB | ASTM | ||
1 | 阀体 | WCB | A2116-WCB |
2 | 弹簧 | 60Si2aMn | AISI 9260 |
3 | 密封圈 | PTFE | PTFE |
4 | 垫片 | PTFE | PTFE |
5 | 排污螺母 | 25 | A105 |
6 | "0" 型密封圈 | 橡胶 | 橡胶 |
7 | 底盖 | 25 | A105 |
8 | 螺钉 | 35 | A193-B7 |
9 | 固定轴 | 1Cr13 | A276-410 |
10 | 滑动轴承 | PTFE& | PTFE& |
11 | 球体 | 1C18Ni9Ti | SS304 |
12 | 阀盖 | WCB | A216-WCB |
13 | 阀座 | 25 | A105 |
14 | 阀杆 | 1Cr33 | A276-410 |
15 | 螺柱 | 35CrMoA | A193-B7 |
16 | 螺母 | 35 | A194-2H |
17 | 压套 | 25 | A105 |
18 | 填料 | PTFE | PTFE |
19 | 支架 | WCB | A216-WCB |
20 | 填料压盖 | WCB | A2116-WCB |
21 | 键 Key | 45 | AISI C 1045 |
The best quality, first-class service Qigao creates more value for you!
"Qigao Valve" expects to continuously improve service quality and strive for excellence. "Sincere service" is the eternal theme of "Qigao". "Qigao" strictly followsIS09001-2000 Quality system certification requirements, strict quality control, responsibility to people, to ensure the healthy operation of production, sales and service. Strengthen communication with users and provide quality products to our customers with perfection and perfect service. Hereby our factory makes the following commitments:
Product Standards:
Products in strict accordance with ChinaGB、HG Standard and USAPISuch as standard design, manufacturing, acceptance. The hardness of the sealing surface meets the requirements of the state and the width exceeds the national standard.
pre-sale service:
Product introduction, technical exchange, non-standard product design, troubleshooting。
Sale service:
A trustworthy contract guarantees timely delivery and keeps in touch with customers. For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.
After sales service:
1、"Qigao" brand product quality period is from the factory12In the month, the implementation of the "three guarantees" service (return, replacement, warranty).
2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions, so as to further improve product quality.
3、Respond quickly to the quality of user complaints, after-sales service personnel rushed to the scene in 24-36 hours (48 hours outside the province).
4、For after-sales service, users are required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of Qigao.
1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:
a、Structure length;
b、Connection Type;
c、Nominal diameter, full diameter, reduced diameter, pipe size;
d、Operating medium and temperature, pressure range;
e、Tests, inspection standards and other requirements
2、The factory can configure various types of driving devices according to customer's specific requirements.。
3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.
4、For futures and order customers, please call us in advance to tell the required valve model, specification, quantity, delivery time and location, and timely transfer to the factory account according to the total 30% deposit or full payment. The rest of the payment is pending. Import before shipment to arrange delivery in time.
Order Process:
1、Customer purchase list fax to021-33872143,Or call us 021-33872141
2、Receive customer purchase list, provide valve model selection and quotation (price list)。
3、Specific agreement: delivery date, special requirements, etc.。
download Google:
1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:
|
|||||
|
|||||
2、The factory can configure various types of driving devices according to customer's specific requirements.。
|
|||||
3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.
|
|||||
4、For futures and order customers, please call us first to tell the required valve model, specifications, quantity, delivery time and location, and press the total30%The deposit or full payment will be remitted to our factory account in time., The rest of the payment will be remitted before shipment to arrange delivery in time.。
|
Sale service:
Trustworthy contract, guarantee timely delivery, keep in touch with customers at any time。
For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.
After sales service:
1、"Qigao" product quality period is from the factory12Month, practice“Three packs”Service (return, replacement, warranty)。
2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions.,
In order to further improve product quality。
3、Respond quickly to the quality of user complaints, after-sales service personnel24-36Hours (outside the province48Hour) rushed to the scene。
4、For after-sales service, the user is required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of “Qigao”.。
statement |
|